# Plaster problems: what each symptom means and costs

> Etching, scaling, delamination, cracks, and mottling in pool plaster, what causes each one, and when a repair is worth doing.

Canonical: https://poolresurfacingguide.com/plaster-problems/

Last updated: 2026-11-09

Plaster problems are almost always visible before they are expensive. Etching, scaling, delamination, cracks, mottling, roughness, and staining each have a distinct look and a distinct cause, and most of them trace back to water chemistry or to preparation done before the finish was troweled. Repair costs run from **$400 to $800** for an acid wash up to **$4,000 to $10,000** for a replaster when the surface has failed as a whole.

## The seven failures

Plaster is a cement and marble-dust coating. It is alkaline, slightly porous, and soluble in aggressive water. Every common problem is a version of one of those three facts.

| Symptom | Usual cause | Typical fix | Cost (estimate) |
|---|---|---|---|
| Chalky, dull patches | Low pH, undersaturated water | Rebalance, then acid wash | $400-$800 |
| Rough, sandy feel | Etching exposing aggregate | Patch, or replaster if widespread | $250-$2,500 or replaster |
| White crust at tile line | High pH, high calcium | Scale removal, chemistry | $300-$900 |
| Hollow thud when tapped | Bond failure, water behind finish | Drained patch | $800-$2,500 |
| Single long crack | Shell movement, settlement | Epoxy injection, stitching | $300-$900 |
| Fine web of lines | Hard trowel, shrinkage | Usually nothing | $0 |
| Brown stains, spreading | Rusted rebar | Chip to steel, treat, patch | $300-$1,200 |

The costs are planning estimates, not quotes. The row that matters most is the fourth: hollow plaster is the one symptom that gets worse at its edges regardless of what the water does next.

## Etching and scaling, the chemistry pair

Etching and scaling are opposites, and a pool can have both in different places. Etching happens when water is undersaturated, so it dissolves calcium out of the plaster to reach balance. The surface goes dull, then chalky, then rough as the cream wears away and the aggregate stands up. Scaling happens when water is oversaturated, so calcium comes out of solution and deposits on the surface, usually as a hard white crust at the waterline and on the tile.

Both are measured by the same four numbers: pH, total alkalinity, calcium hardness, and water temperature. A pool at pH 7.4 with alkalinity at 80 to 120 ppm and hardness in range does neither. A pool left at pH 7.0 for a summer etches. A pool run at pH 8.0 with hard fill water scales.

The asymmetry is what catches owners. Etching removes material permanently. Scaling can be removed, but the removal takes a little surface with it.

## Delamination and cracks

Delamination is the failure that ends a finish's life. Water gets behind the plaster through a crack, a fitting, or a bond failure at application, and the sheet comes away from the shell in plates. Tap the wall with a screwdriver handle: a ring means bond, a dull thud means hollow. [Delamination signs](https://poolresurfacingguide.com/delamination-signs/) covers how far the problem usually runs once it starts.

Cracks are a separate question. A single line that crosses the surface is structural until proven otherwise, and it should be injected with epoxy rather than smeared over. A fine web of shallow lines is craze cracking, which is cosmetic, common on hard-troweled plaster, and usually not worth repairing. The test is whether a crack widens, returns after repair, or has rust staining at its edge.

## Cosmetic against structural

| Signal | Cosmetic | Structural |
|---|---|---|
| Discoloration only | Yes | No |
| Surface roughness | Often | Sometimes |
| Hollow sound when tapped | No | Yes |
| Crack that returns | No | Yes |
| Rust staining | No | Yes |
| Water loss | No | Yes |

The table is a triage tool, not a diagnosis. Two or more signals in the right column mean the finish is at the end of its life regardless of how the pool looks from the deck, and the money spent on patches will not change the outcome.

## What the repairs cost

- **Acid wash:** $400 to $800. It removes stains and a thin layer of surface, and it is maintenance rather than restoration.
- **Spot patch:** $250 to $600. Appropriate for a chip or a small area of roughness.
- **Crack injection:** $300 to $900. Epoxy injection on one to three cracks.
- **Drained delamination repair:** $800 to $2,500. Drain, strip hollow plaster, repair, patch, refill.
- **Replaster:** $4,000 to $10,000. The full range for a typical residential pool.

The arithmetic that decides between them is per square foot. A 60 square foot delamination at $2,000 is $2,000 ÷ 60 = **$33.33 per square foot**. A full replaster on an 855 square foot pool at $6,500 is $6,500 ÷ 855 = **$7.60 per square foot**. The local repair costs more than four times as much per foot of surface treated. [Pool plaster repair cost](https://poolresurfacingguide.com/pool-plaster-repair-cost/) runs the numbers on the middle cases.

## Five steps when you find a problem

1. Photograph the area with something for scale, and note whether it is growing week to week.
2. Test pH, alkalinity, calcium hardness, and stabilizer before you call anyone, because the water record is the diagnosis.
3. Tap the surrounding plaster with a screwdriver handle and mark any hollow areas with tape.
4. Get a repair quote and a replaster quote on the same pool, each with the interior square footage stated.
5. Ask what the repair will look like after cure, since color match is the complaint that follows most patches.

Step two is the one owners skip. A surface that has been etched by two summers at pH 7.0 will etch again after a patch unless the water is corrected, and the second failure is usually blamed on the contractor. [Plaster maintenance](https://poolresurfacingguide.com/plaster-maintenance/) covers the targets that prevent it.

## The short version

Most plaster problems are chemistry problems that have become surface problems. Etching and scaling come from pH and calcium balance, delamination and cracks come from preparation and shell movement, and staining usually means steel is corroding. Fix the water first, repair locally only when the damage is small and the surrounding finish is sound, and replaster at $4,000 to $10,000 when the symptoms appear in more than one place at once. [Plaster cost](https://poolresurfacingguide.com/plaster-cost/) covers what replacement involves.